null
SpeedyBee

SpeedyBee F405 V4 BLS 55A 30x30 FC&ESC Stack

(No reviews yet) Write a Review
SKU:
PEBLH49
Condition:
New
Shipping:
Calculated at Checkout
  • SpeedyBee F405 V4 BLS 55A 30x30 FC&ESC Stack
  • SpeedyBee F405 V4 BLS 55A 30x30 FC&ESC Stack
  • SpeedyBee F405 V4 BLS 55A 30x30 FC&ESC Stack
KES13,500.00

SOLD OUT

Frequently bought together:

Description

Specifications
Product Name SpeedyBee F405 V4 30x30 Flight Controller
MCU STM32F405
IMU(Gyro) BMI270
USB Port Type Type-C
Barometer Built-in
OSD Chip AT7456E chip
BLE Bluetooth Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)
DJI Air Unit Connection Way Two ways supported: 6-pin connector or direct soldering.
Blackbox MicroSD Card Slot *Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose 'Overwrite format' then format your card. Also check out here for the recommended SD cards or buy the tested cards from our store.
BetaFlight Camera Control Pad Yes(CC pad on the front side)
Current Sensor Input Supported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0.
Power Input 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)
5V Output 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A.
9V Output 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 2A.
3.3V Output Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
4.5V Output Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal M1 - M4 on bottom side and M5-M8 on front side.
UART 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection), UART5(Dedicated for ESC telemetry)
ESC Telemetry UART R5(UART5)
I2C Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
Traditional Betaflight LED Pad Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
Buzzer BZ+ and BZ- pad used for 5V Buzzer
BOOT Button Supported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input Supported. Named as RS on the front side.
SmartPort Use any TX pad of UART for the SmartPort feature.
Supported Flight Controller Firmware BetaFlight(Default), EMUFlight, INAV
Firmware Target Name SPEEDYBEEF405V3
Mounting 30.5 x 30.5mm( 4mm hole diameter)
Dimension 41.6(L) x 39.4(W) x 7.8(H)mm
Weight 9.6g
Product Name SpeedyBee BLS 50A 30x30 4-in-1 ESC
Firmware BLHeli_S JH50
Wireless Configuration Full Configuration Supported in the SpeedyBee app
PC Configurator Download Link https://esc-configurator.com/
Continuous Current 55A * 4
Burst Current 55A(5seconds)
TVS Protective diode Yes
External Capacitor 1000uF Low ESR Capacitor(In the package)
ESC Protocol DSHOT300/600
Power Input 3-6S LiPo
Power Output VBAT
Current Sensor Support (Scale=386 Offset=0)
Mounting 30.5 x 30.5mm( 4mm hole diameter)
Dimension 45.6(L) * 44(W) * 6.1mm(H)
Weight 13.8g
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
SpeedyBee F405 V3 STACK
View AllClose

0 Reviews

View AllClose

Related Products

Related Products

SOLD OUT
30A Simonk ESC with BEC 30A Simonk ESC with BEC
Quick view

30A Simonk ESC with BEC

Readytosky

KES1,500.00
30A Simonk Brushless speed controller ESC for MultiCopter KK Multi-Copter Quad X-flying Description: Highest efficiency 100% N-FET design.
SOLD OUT
Emax 20A BLHeli ESC
Quick view

Emax 20A BLHeli ESC

EMax

KES1,500.00
Emax BLHeli Series 20A ESC Speed Controller 2A 5V BEC for RC Multicopter  Features: - Rotation direction of the motor is programmable: normal, revers
SOLD OUT
Emax BLHeli 30A Brushless ESC Emax BLHeli 30A Brushless ESC
Quick view

Emax BLHeli 30A Brushless ESC

EMax

KES1,600.00
Features:Use authentic electronic components to ensure high quality and enhance the current endurance ability of the ESC.Based on BLHeli firmware,optimized for high performance with great linearity...
SOLD OUT
30A Brushless Motor Speed Controller ESC 30A Brushless Motor Speed Controller ESC
Quick view

30A Brushless Motor Speed Controller ESC

Readytosky

KES1,500.00
A Electronic Speed Controller(ESC) for Brushless DC Motors.This ESC is specifically made for quadcopters and multirotors and provides faster and better motor speed control giving better flight...
SOLD OUT
Readytosky 2-6s 40A opto esc Readytosky 2-6s 40A opto esc
Quick view

Readytosky 2-6s 40A opto esc

Readytosky

KES2,000.00
Brand: ReadytoskyCont.Current: 40ABurst Current(10sec):60ABEC:NoneLipo:2-6SProgramming: Timing(high/middle) Usage: RC Multintegrated circuitopter APAC means Asia-Pacifintegrated circuit Version,the...