TESCA
Switching Mode Power Supply (SMPS) with 2 meters - Order Code 36205
(No reviews yet)
Write a Review
- SKU:
- 36205
- Shipping:
- Calculated at Checkout
Frequently bought together:
Description
Order Code: 36205
Name: Switching Mode Power Supply (SMPS) with 2 meters
SPECIFICATION
Experimental Training Board has been designed to practically demonstrate the operation of a Switching Mode Power Supply. The Switching waveform and various voltages can be observed on the test points provided on the panel.
Practical experience on this board carries great educative value for Science and Engineering Students.
Object:
01. To observe various voltages and Switching waveforms on the SMPS Circuit.
02. To demonstrate the effect of load variation on the switching waveform.
03. To measure the following :
(a) Ripple.
(b) Load regulation.
(c) Line regulation.
Features:
The board consists of following built-in parts :
01. Complete SMPS circuit based on IC-723, having output 5V D.C. at 1.5 Amp.
02. D.C. Voltmeter, 65mm rectangular dial to read 0-30V.
03. D.C Ammeter, 65mm rectangular dial to read 0-2Amp.
04. Three fixed value loads.
05. Mains ON/OFF switch, Fuse and Jewel light.
* The unit is operative on 230V ±10% at 50Hz A.C. Mains.
* Adequate no. of patch cords stackable from rear both ends 4mm spring loaded plug length ½ metre.
* Good Quality, reliable terminal/sockets are provided at appropriate places on panel for connections & observation of waveforms.
* Strongly supported by detailed Operating Instructions, giving details of Object, Theory, Design procedures, Report Suggestions and Book References.
Practical experience on this board carries great educative value for Science and Engineering Students.
Object:
01. To observe various voltages and Switching waveforms on the SMPS Circuit.
02. To demonstrate the effect of load variation on the switching waveform.
03. To measure the following :
(a) Ripple.
(b) Load regulation.
(c) Line regulation.
Features:
The board consists of following built-in parts :
01. Complete SMPS circuit based on IC-723, having output 5V D.C. at 1.5 Amp.
02. D.C. Voltmeter, 65mm rectangular dial to read 0-30V.
03. D.C Ammeter, 65mm rectangular dial to read 0-2Amp.
04. Three fixed value loads.
05. Mains ON/OFF switch, Fuse and Jewel light.
* The unit is operative on 230V ±10% at 50Hz A.C. Mains.
* Adequate no. of patch cords stackable from rear both ends 4mm spring loaded plug length ½ metre.
* Good Quality, reliable terminal/sockets are provided at appropriate places on panel for connections & observation of waveforms.
* Strongly supported by detailed Operating Instructions, giving details of Object, Theory, Design procedures, Report Suggestions and Book References.
Related Products
Related Products
Diac Characteristics with Power Supply and 2 meters - Order Code 36167
TESCA
$0.00
Order Code: 36167Name: Diac Characteristics with Power Supply and 2 meters
SPECIFICATION
Experimental Training Board has been designed specifically to stu
Multivibrators with power supply and 1 meters - Order Code 36195
TESCA
$0.00
Order Code: 36195Name: Multivibrators with power supply and 1 meters
SPECIFICATION
Experimental Training Board has been designed specifically for the stud
Scaling Amplifier with power supply and 2 meters (C.R.) - Order Code 36261
TESCA
$0.00
Order Code: 36261Name: Scaling Amplifier with power supply and 2 meters (C.R.)
SPECIFICATION
Experimental Training Board has been designed specifica
Zener regulated Power Supplies in 2 meters (C.R.) - Order Code 36207
TESCA
$0.00
Order Code: 36207Name: Zener regulated Power Supplies in 2 meters (C.R.)
SPECIFICATION
Experimental Training Board has been designed specifically fo
D.C. Power Supplies and 2 dual range meters - Order Code 36188
TESCA
$0.00
Order Code: 36188Name: D.C. Power Supplies and 2 dual range meters
SPECIFICATION
Experimental Training Board has been designed specifically for the