Linear I.C. Trainer with Power Supply, Oscillator and 2 Multi Range Meters - Order Code 36101

SPECIFICATION

1. 0-30V D.C. at 500mA, continuously variably unregulated Power Supply.
2. ± 12V D.C. at 250 mA, IC Regulated Power Supply.
3. ± 6V D.C. at 200 mA, IC Regulated Power Supply.
4. 1 KHz square wave signal source with variable output level.
5. 100 Hz sine wave signal source with variable output level.
6. Pulser for generating trigger pulses.
7. D.C. Ammeter, 65mm rectangular dial with switch selectable ranges of 50 mA,250mA and 500mA.
8. D.C. Voltmeter, 65mm rectangular dial, dial with switch selectable ranges of 100mV,1V and 40V.
9. Two toggle switches, NPN power transistor 2N 3055, Transistor BC 177, Two IC 741 Three IC 3130, IC 710, IC 723, IC 3085, IC 555, IC 566, IC 565,IC 7812, IC 7912, Electronic Load, 8 potentiometers, 45 fixed value resistors, 22 capacitors, 3 silicon signal diodes, 3 zener diodes, LED, 3 sets of 3 interconnected sockets each for multi-connections wherever required.

1. To measure the quiescent supply current
2. To null the offset voltage
3. To measure open-loop voltage gain under closed loop condition.
4. To measure output resistance
5. To measure differential input resistance
6. To measure unity gain bandwidth
7. To measure the rated output
8. To measure the slewing rate
9. To measure the full power response
10. To measure input offset voltage
11. To measure input bias and offset current
12. To measure input noise voltage
13. To measure input noise current
14. To measure Common Mode Rejection Ratio (CMRR)
15. To measure Common Mode Input Resistance (CMIR)
16. Application as Inverting amplifier
17. Application as Non-inverting amplifier
18. Application as difference amplifier
19. Application as Inverting summing amplifier
20. Application as Non-inverting summing amplifier
21. Application as D.C. Voltage follower
22. Application as A.C. Voltage follower
23.  Application as differentiator
24. Application as Integrator
25. Application as semi Log-amplifier
26. Application as unipolar limiter
27. Application as bipolar limiter
28. Application as positive peak clipper
29. Application as negative peak clipper
30. Application as AC-DC converter
31. Application as High Pass Filter
32. Application as Low Pass Filter
33. Application as Triangle to Sine Wave Converter
34.  Application as 500Hz-5KHz Square Wave Generator
35. Application as Wien-Bridge Oscillator
36. Application as Pulse Generator
37. Application as linear to log potentiometer
38. Application as random noise generator 

1. Application as high input impedance voltage follower
2. Application as pulse generator with independent control of ONand OFF periods
3. Application as active full wave rectifier without using diodes

1. To measure open loop voltage gain under closed loopcondition
2. To measure output resistance
3. To measure differential input resistance
4. To measure unity gain bandwidth
5. To measure the rated output
6. To measure the slewing rate
7. To measure the full power response
8. To measure input offset voltage
9. To measure input bias and offset current
10. To measure input noise voltage
11. To measure input noise current
12. To measure Common Mode Rejection Ration (CMMR)
13. To measure Common Mode Input Resistance (CMIR)
14. Application as a comparator
15. Application as a pulse width modulator
16. Application as a level detector
17. Application as Schmitt Trigger 

1. Application as pulse width modulator
2. Application as pulse position modulator
3. Application as linear ramp generator
4. Application as 50% duty cycle oscillator
5. Application as Monostable Multivibrator
6. Application as Astable Multivibrator
7. Application as Frequency divider
8. Application as Schmitt trigger
9. Application as Event failure alarm
10. Application as Sine to Square Wave Converter

1. To study the linearity and accuracy of output waveforms

1. Measurement of center frequency ‘fo ’
2. To study Vco sensitivity and linearity
3. Measurement of capture range and lock range
4. To study locking of V co to harmonic of input signal
5. Detection of F.M. Signal 

1. To measure Line Regulation
2. To measure Load Regulation
3. To suppress oscillations at input and output
4. To study minimum input to output voltage Difference required for proper operation
5. To increase the output voltage using resistors
6. To increase the output voltage using zener diodes
7. To continuously vary the output voltage

1. To measure Line Regulation
2. To measure Load Regulation
3. To measure Ripple Rejection
4. Application as basic voltage regulator
5. Application as Low voltage regulator (2 to 7V)
6. Application as High voltage regulator (7 to 21V)
7. Application as increased current output voltage regulator Using external NPN power transistor
8. Application as fold back current limiting regulator

1. To measure Line Regulation
2. To measure Load Regulation
3. To measure Ripple Rejection
4. Application as 3 to 23V variable output voltageregulator
5. Application as fixed voltage regulator
6. Application as current regulator
7. Application as High Gain Amplifier (upto100KHz)

For Product Catalog click below
Download PDF