Brushed DC Motor Driver

Highlights: The module supports high-level trigger, low-level trigger, switch control, PWM control; The use of imported dual-MOS parallel active output, lower internal resistance, current, power strong, continuous current at room temperature is 10A,...

Product description: Double H driver module uses  L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard...

Overview: The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). EasyDriver requires a 7V to 30V supply to power the motor...

Features: - Signal optocoupler isolation input,With isolation and undervoltage protection and suit for EMC specifications for electromagnetic compatibility - It is electrostatic discharge circuit and stable and reliable, industrial grade. - Dual motor...

Instruction:MOSFET is an electronic device having a good switching characteristics, is widely used in the electronic switch circuit needs, such as switching power supplies and motor drives, and a lighting dimming.We designed this four-way MOSFET switch...

Description: This is essentially a ramped up version of our Ardumoto motor driver shield. For this monster shield we’ve replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry...

Driver: L298N Dual H Bridge DC Motor Driver IC Driven the terminal supply area Vs: +5V ~ + 35V; Such as need to take power inside the board, supply area Vs: + 7V ~ + 35V Driven part of the maximum current Io: 2A The logical part of the voltage of...

Application: output port can control high power devices, such as motors, lamps, LED lamp strings, DC motors, micro water pumps, electromagnet valves; it can input PWM to control motor rotate speed and the brightness of lamp    Interface: 1...

L293D motor shield, the input voltage DC4.5-25V-600mA output current capability per channel-1.2A Peak output current (non repetitive) Per Channel-Enable Facility-Over-temperature protection-Logical "0" Input voltage upto 1.5 V(HIGH NOISE...

Description: Rated Voltage: DC5V4-phaseReduction Ratio: 1/64Step Torque Angle: 5.625/64DC Resistance: 200±7% (25)Insulation Resistance: >10M (500V)Dielectric Strength: 600V AC / 1mA / 1sInsulation Grade: ANo-load Pull in Frequency:...

IRF520 MOS FET Driver Module for Arduino Features: 1. Size: 33*24mm.2. Weight: 10g.3. Voltage: 3.3V, 5V.4. Ports: digital quantity level.5. Output load voltage: 0~24V.6. Output load current: <5A (1A above need to add heat sink) 7. Platform:...

Ardumoto L298P AVR/LPC/STM32 UNO/MEGA Motor Driver  Description:- The new version of this shield allows for either 3.3 or 5v logic, a separate and more robust VIN connection, and the PWM input has moved to pin 3.- This is a motor shield for...

Description: ULN2003 is a high voltage and high current Darlington transistor array products with high current gain, high operating voltage, wide temperature range, with a strong load capacity and other characteristics, adapted to the requirements of...

Description: 1. Function: Use the low level to control the high level. Such as the use of single-chip 3V or 5V voltage control 9V or 12v voltage. 2. HVCC should not exceed 24V. Output OUT1 / OUT2 / OUT3 / OUT4 output current equal to HVCC / 5.1K,...

MOSFET is an electronic devices with good switching characteristics. It is widely used in circuits, such as power supplies switching ,motor drives, lighting dimmer and so on. Relay is another kind of module with switching characteristics. Since relay...

MOS FET electronic switch module, you can use low-voltage and small current to control high-power equipment, motors, light bulbs, high-power LED. For example: you want a device output 5V signal, control a 12V motor switch. This module can be achieved...

Description: motor drive module is ideal for use in battery-powered smart car, toy cars, robots. Supply voltage 2V ~ 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to...

Product description: The L298N driver module, using ST L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface, you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easily control the DC motor speed...

Description: Dimension: 3.2cm x 2.4cm x 1.8cm (approx) Infrared sensor with control circuit board The sensitivity and holding time can be adjusted Working Voltage Range: DC 4.5V- 20V Current drain:<60uA  Voltage Output: High/Low level...

Overview: This is essentially a ramped up version of Ardumoto motor driver shield. For this monster shield we\'ve replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. We've also beefed up the support circuitry so this board is...